Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
Listed here in the next paragraph you can discover some high-quality help and advice concerning A Step-by-Step Guide to Installing a Bathtub.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily easily accessible, the task can relocate speedily; if you have to open a wall to remove the old tub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed job, it is better to consider employing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This post will help you install a new bathtub in your washroom if you have actually currently gotten a brand-new tub and don't require to transform the setup of your previous supply of water pipes.
Your devices and also product list must make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome as a result of the limited gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Protect the tap in place with the supplier provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Using both wood boards under its feet, place the tub in the called for setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the tub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been used a minimum of once as this will settle it into its final setting.
Getting ready for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece about How to Install a Bathtub Yourself when doing a lookup on the internet. Sharing is caring. You won't know, you could be doing someone a favor. I praise you for your time. Come back soon.
Book Appointment Report this page